Showing all 31 results
Automatic CV Brake Pads Friction Mixes Weighing Machine is used to weigh the friction mixture and divide then into small cups according the set weight of input raw materials for brake pads. Material tank can be divided into two bins, and weigh two different mixture at the same time. Technical Parameters： BL-PC46–FMW(for pc brake pads)…
CV Brake Pads Brake-In Strips Gluing Machine is designed to coat the brake-in strips on the friction surface. Coating different pattern of the glue strips shall change the pattern molds on this machine. Technical Parameters： Size of the machine(L x W x H): 650mm x 800mm x 1600mm Working Table Size(L x W): 280mm x…
CV Brake Pads Cleanning Machine Before Powder Coating is used to clean the back plate side of brake pads before powder coating, to guarantee a smooth coating performance. Technical Parameters Production Capacity: About 3000 pcs/hour Speed: 9 meters/minute Brush: 3 Pcs Brush Motor: 1.1kw*3 Transport Motor: 0.75kw Dust Collect: Seperately for single brush
CV Brake Pad Press Machine Group Set with Weighting System is a combination of a weighing system, 1 to 6 units of hot pressers, automatic manipulators on travelling rack, and other accessories. It is mainly responsible for the following 6 procedures during the whole production process: One-layer or double-layer friction mixes weighing Mixes flattening(pre-pressingif with…
Brake Pads Automatic Material Weighting and Mixing System is used for weighing raw materials automatic before mixing.This system operates fully automatic base on the friction material formulation which is saved in PLC. If operator selects saved formulation, automatically weighing and collecting different weighed material and then discharge to the linked Mixer. Feature: -The whole process…
Brake Pads Plough-Chopper Friction Materials Mixer applied the advanced technology of three-dimensional circulating mixing principle, are designed to mix friction materials automatically. It adopts new high-speed mixing blades and scientific mixing barrel, pneumatic feeding, to ensure that no dead angle in the chamber. It is equipped with cold water circulating cooling system, adapting to the…
Brake Pad Shot Blasting Machine is used for surface cleaning of brake pad steel back plates, to present a natural steel appearance. It can remove the oxidized layer of the backing plates, and also optimizes the surface before gluing to improve the gluing quality. After shot blasting, the Brake Pads Backing Plates will get a…
Brake Pads Backing Plates Ultrasonic Clean Machine is used for steel backing plate surface degreasing with ultrasonic before gluing. Specification: – Size:L8565*W2120*H1290mm – Load and Lay Off Material Platform (Length/Width):Each With 500×440mm – Cleaning Tank Inner Size:L2300×W440×H200mm – Spray Rinse Inner Size:L800×W440×H150mm – Compressed Air Cutting Water Inner Size:L600×W440×H150mm – Hot Oven Inner Size:L2998×W440×H150mm – Conveyor Belt Width:400mm – Liquid Storage Tank:L700*2…
Brake Pads Backing Plates Gluing Machine adopts glue spraying room, conveyor, touch screen control, pneumatic system. The steel backing plates are put on the customized spray adhesive tablets by workers, automatically sent to spray adhesive by conveyor, automatically put in the spray adhesive and then into the connected oven to dry and cool. Spray Adhesive…
Brake Pads Equal Pressure Hot Press Machines are the most advanced type press machines used for making OE qualified high end passenger car brake pads, with its high production efficiency, and good production quality. The machine adopts advanced floating cylinder design to ensure that each brake pad in the same mold is subject to the…
Brake Pads Disc Grinding Machine is to process the surface grinding of all kinds of brake pads, which doesn’t require fixtures to hold brake pads, brake pads are all fixed on the grinder disc by electromagnets. It can do fine grinding, coarse grinding and dust cleaning at the same time. It also equipped with step-less speed…
Brake Pads Hot Curing Oven is used for brake pads, Brake Linings and all the friction material curing procedure, to speed up the chemical reaction inside of the mixed friction materials to a reasonable and stable level. Technical Parameters: – Temperature operating range: Room temperature to 300℃ – Temperature equality degree: within ±4℃ (When the temperature…
Brake Pads Sand Blasting Machine is used for cleaning the out surface of a finished brake pad by silicon sands to present a clean and smooth appearance before powder coating, which is equipped with an Air Compressor to blow out silicon sands. Technical Parameters： – Working Room Size: Width ≤500mm – Application Range: Metal or Nonmetal…
Brake Pads Friction Mixes Weighting Machine is used for weighing friction mixes automatic, the accuracy of weighing tolerance can be narrowed down to 0.1-0.5g/cup, adjustable on the PLC interface. Technical Parameters： – The weighing range: 0 – 250g / cavity for passenger car brake pads. – Weighing tolerance: 0.1-0.5g, adjustable. – Operation Mode: P.L.C. Controlled. –…
Brake Pads Electrostatic Powder Coating Line applies Infrared Heating Technology, which is 30-50% energy saving compared to electric heating technology with same electric power, the ordinary electric heating tunnel applies heat conduction to transfer the heat energy to brake pads, however, the infrared heating tunnel applies thermal radiation by special short and medium infrared waves…
Brake Pad Printing Machine is used for printing company logo, words on the Brake Pads. Technical Parameters： – The printing color: Single Color – Dynamic type: Pneumatic – Ink cup diameter (inside and outside): 90mm – Max: plate size(mm): 100*250*10mm – Max: pin size(mm): 70*130 – Printed products are highly(mm): 1-200(300) – Before and after the trip: 175 – Printing speed/hr: 2300pcs/hr,…
Brake Pad Dynamo-Meter Test Machine is used to process the brake performance test and NVH test on assembled brake by combining mechanical inertia and electrical inertia, it permits the replication of braking performance for a wide range of vehicle sizes. Inertia simulation allows for precise vehicle inertia points to be tested via the drive motor…
Brake Pads Chase Test Machine is designed and engineered to uate the frictional characteristics of materials used in braking systems in accordance with world recognized standard J661, ISO 7881, GB/T 17469-98 test procedure. The machine may be effectively utilized for quality control, research and development, or certification type applications, with highly repeatable results. Technical Parameters：…
Brake Pads Compression Test Machine is designed to check the dimension change of disc brake pads under the influence of heat and pressure, in accordance with world recognized standard ISO6310-1981-07-01, ISO6310-2001 as well as ISO6313-1980-06-01. Technical Parameters： – hydraulic cylinder stroke: 60mm – hydraulic cylinder piston diameter: 90mm – displacement sensor travel: 2mm – the measurement accuracy: 0.01mm…
Brake Pads Friction Wear Test Machine provides precise data on frictional material performance and wear characteristics in accordance with Chinese Standard GB5763－98; GB5764－98 and Japanese Standard JIS D4411-1993. Technical Parameters： – Friction plate：Material HT250; Hardness：HB180－220； – Rotating speed: 480 ± 10 r/min; – Driving motor: 7.5 kw, 970 r/min; – Sample Size: 25 x 25mm; Thickness: 5 – 7…
Brake Pads Ink Jet Printing Machine is used for printing your information on the brake pads, such as item No., friction level or production day, only words. – Single-button start and shutdown – No need to clean the nozzle – Menu – driven way to edit – English and Chinese user interface – Touch screen with printer status indicator…
Brake Pads Shear Test Machine measures the force required to shear the friction lining from the backing plate to test its strength. It combines precise test control with ease of operation, generating accurate results, and it is an ideal instrument for research and development or quality control. This machine meets the standards of major brake…
Brake Pad Factory Dust Collect Machine is used for cleaning the dust created during all the procedures, such as surface slotting, chamfering and grinding in the production. Technical Parameters： – Sack: Polyester needle felt – Racks: Galvanized – Pulse valve: 1.5″Right Angle – Dusk Valve: 300×300 – Turbine: 18.5KW – Voltage/Frequency: Customized Click To See More CV Brake Pad Machines
Brake Pads Compressed Air Machine is an equipment that supply the compressed air power for some machines and equipments for brake pads production. Technical Parameters: – Screw Group:4,5 Tooth Rotor – Compressing Format: Continuous,Single Stepped – Compressed Air Outlet Pressure:P2=0.8MPa – Cooling Mode:Air Cooling – Heating Platen Area: 550mmX450mm – Compressed Air Outlet Temperature:10℃～15℃ Higher Than The Environment Temperature – Lubricating Oil Quantity:About…
CV Brake Pads Vulcanizing Hot Press Machine is the most popular type press machine used for making both passenger car and commercial vehicle brake pads, with its high production efficiency, and good production quality. One operator can handle 2 units such press machines, very efficient and labor saving. Technical Parameters： – Max Clamping Force: 400Ton(4000KN) – Heating…
CV Brake Pads Combined Grinding Machine combines procedures of slotting, coarse grinding, fine grinding, and dust cleaning at one machine with high efficiency. Technical Parameters： Grinding Unit Spec. Rough Surface Grinding Unit: 1 Set (Vertical spindle 11.25 Kw) Slot Grinding Unit: 1 Set (Horizontal spindle 7.5 Kw) Fine Surface Grinding Unit: 1 Set (Vertical spindle…
CV Brake Pads Laser Printing Machine is used for printing all kinds of logo and words on the surface of finished brake pads, pc brake shoe linings, cv Brake Linings, anti-noise shims as well as backing plates. It’s clean, safe and fast, and can be connected into the automatic production line with other machines. Technical…
CV Brake Pads Roller Gluing Machine for brake pad back plates, which includes three parts in this machine, which is widely used in brake pad factory, with a higher production efficiency, and good gluing performance. Technical Parameters： – ROLLER GLOWING MACHINE Adhesive Machine Infrared Heating Tunnel Fan Cooling Tunnel – ADHESIVE PART : Gluing Roller:…
CV Brake Pads Slot Machine is a special machine for processing slot and chamfer on disc brake pad. It is very easily adjustable and suitable for any model of passenger and commercial vehicle brake pads in the market, which can meet up with high-volume production needs. Technical Parameters： – Slotted motor: 4KW 2880 rev /…
CV Brake Pads Strips Gluing Machine is designed to coat the brake-in strips on the friction surface. Coating different pattern of the glue strips shall change the pattern molds on this machine. Technical Parameters： Size of the machine(L x W x H): 650mm x 800mm x 1600mm Working Table Size(L x W): 280mm x 350mm…
Vertical Brake Pad Friction Materials Mixer is used for mixing friction materials. It is widely applied in the production of Brake Pads, and Brake Shoes.It adopts new high-speed mixing blades and scientific mixing barrel, pneumatic feeding, to ensure that no dead angle in the chamber. It is equipped with cold water circulating cooling system, It…